The 074829 (also know as F074829) is a 1/16 DIN digital temperature controller for the S2 type K thermocouple for the Tutco SureHeat Jet heaters 074718 and 074719. This controller goes with the 074835 inlet temperature limit (relay output) circuit for the S1 type K thermocouple also for the Tutco SureHeat Jet heaters.

The 074835 (also know as F074835) is an inlet temperature limi circuit for S1 type K thermocouple for the SureHeat Jet heaters 074718 and 074719. This relay goes with the 074829 exit temperature controller for the S2 type K thermocouple also for the SureHeat Jet heaters.

075526 (F075526) TUTCO SUREHEAT SureHeat JET control panel is a closed-loop temperature control system for SureHeat JET heaters. It comes with a NEMA 4X enclosure,a 35A 240V 1ph electrical rating, AND a RS-232 communication port.

This 075615 (ALSO KNOWN AS F075615) TUTCO SUREHEAT Air Heater Is A Complete Heater With A Self Contained Blower And Digital Display Temperature Controller. This Skorpion Heater Is Ready To Be Plugged Into An Electrical Outlet And Used For Your Heating Application.

This 075616 TUTCO SUREHEAT air heater is a complete heater with a self contained blower and digital display (closed loop PID) temperature controller.

This 075744 (F075744) high flow nozzle is an accessory that can be attached to all Skorpion air heater models. It is made of welded sheet metal with a 21mm (1 inch) diameter opening. This nozzle slips onto the Skorpion heater and is held in place using a set screw.

This 075745 (F075745) standard flare nozzle is an accessory that can be attached to all Skorpion air heater models. It is made of welded sheet metal with a 150mm by 12mm (6 by 0.5 inch) opening. This nozzle slips onto the Skorpion heater and is held in place using a set screw.

This 075746 (F075746) wide flare nozzle is an accessory that can be attached to all Skorpion air heater models. It is made of welded sheet metal with a 12 by 0.16 inch opening. This nozzle slips onto the Skorpion heater and is held in place using a set screw.

This 075835 (or F075835) TUTCO SUREHEAT Air Heater Comes With An Integrated Digital Display (Closed Loop Pid) Temperature Controller. This Skorpion Heater Is Ready To Be Hooked Up To An External Air Source And Plugged Into An Electrical Outlet.

This 075869 TUTCO SUREHEAT Air Heater Comes With An Integrated Digital Display Temperature Controller. This Skorpion Heater Is Ready To Be Hooked Up To An Air Supply And Plugged Into An Electrical Outlet.

This 076008 TUTCO SUREHEAT Air Heater Is A Complete Heater With A Self Contained Blower And Digital Display (Closed Loop Pid)temperature Controller. This Skorpion Heater Is Ready To Be Plugged Into An Electrical Outlet And Used For Your Heating Application. Feel Confident Purchasing This TUTCO SUREHEAT Heater Knowing It Comes With An Outstanding Three Year Warranty.

This 076029 (OR F076029) TUTCO SUREHEAT Air Heater Comes With An Integrated Digital Display Temperature Controller. This Skorpion Heater Is Ready To Be Hooked Up To An Air Supply And Plugged Into An Electrical Outlet.

The 076197 TUTCO SUREHEAT Max HT Air Heater is designed for 36000 watts of power, 480 voltage three phase, and a maximum amperage of 43.4 amps. This part has been replaced by the F077085 or 077085 Tutco SureHeat Max HT hot air heater. Call Jobco Inc. for quantity pricing or special pricing at 479-424-1300.

The 076250 TUTCO SUREHEAT Max Ht Air Heater Is Designed For 18000 Watts Of Power, 240 Voltage Three Phase, And A Maximum Amperage Of 43.4 Amps. Call Jobco Inc. For Quantity Pricing Or Special Pricing At 479-424-1300.

076361 Digital temperature controller, 1/16 DIN, 4-20mA is a direct replacement for the 070429 obsoleted temperature controller and is used with 066823 closed-loop power control. The 076361 is the digital controller used for many of the TUTCO SUREHEAT hot air process heaters.

076418 TUTCO SUREHEAT threaded inline heater is a Style B design that can handle a maximum air pressure of 150 psi (10 bar). This TUTCO SUREHEAT air heater model allows a minimal air leak out through the power wires. This threaded inline hot air heater is designed for high pressure air applications needing a 2.5" NPT sized heater.

This 076436 Tutco SureHeat Skorpion Air Heater Is A Complete Heater With A Self Contained Larger 4500 Watt Blower (22 To 45 Scfm Maximum Flow Rate With 60hz Pwer Supply) And Digital Display (Closed Loop Pid)temperature Controller. This Model Is Ideal For International Applications That Run With 50 Hz Power,

The 076518 TUTCO SUREHEAT SureHeat Max HT Air Heater is designed for 18000 watts of power, 480 voltage three phase, and a maximum amperage of 21.7 amps. Call Jobco Inc. for quantity pricing or special pricing at 479-424-1300.

The 076525 (or F076525) TUTCO SUREHEAT threaded inline heater is a Style B design with 24" long 10ga fiberglass leads rated for 105 deg C and 45 psi (3 Bar) maximum static pressure. This threaded inline hot air heater is designed for high pressure AND higher inlet temperature applications needing a 1.25" FNPT fitting on the inlet end and a 1.25" MNPT fitting on the exit end. This HIGH TEMPERATURE hot air heater provides a maximum process heat of 1652 degrees F at 11 SCFM by providing 6000/8000 maximum watts at 208/240 volt 1P power and 29/34 max. amps. The heater is 1.7" OD by 20" long with a 316 stainless steel housing. The recommended minimum airflow for this heater is 3 SCFM (85 SLPM), and the maximum inlet temperature should be no higher than 120 degrees F.

These heater elements are shipped in a box containing 2 pieces. Heater elements must be ordered in multiples of 2 pieces! Price is the cost for one heater element.



The 076541 (or F076541) TUTCO SUREHEAT Hot Air tool provides a triple pass exchange housing. The Serpentine VI heater's triple pass exchange housing uses incoming air to travel (AND COOL) down the outside shell of the heater. The air then travels through a slot and into air holes, where it rapidly warms as it flows over the heater element and exits out of the heater. This hot air heater provides a maximum process heat of 1500 degrees F by providing 6,000 watts at 240 volt power and 25 max. amps. The heater is 10.88" long with a 1.25" outside diameter. The housing for this heater is part number 057088.

Heater life can last up to 5000 hours if the manufacturer's guidelines are followed. Compressed air or air from a regenerative blower can be used to supply CLEAN and DRY air to your heater. Dirt, grease, oil, oil vapors, corrosive gases, and reactive gases will damage the air heater. Compressed air at typically 100 p.s.i. will need to be filtered to eliminate oil from the air supply. Compare this TUTCO SUREHEAT heater to these OEM part numbers HT12238 or 003-10032 as a possible replacement. TUTCO SUREHEAT Air/Inert Gas heaters should be used to heat air or an inert gas only. Use with explosive gases or in an explosive ambient can result in an explosive event, possibly leading to a serious accident or injury.

 

The 076619 (or F076619) TUTCO SUREHEAT threaded inline heater is a Style A design that should be used whenever an absolute leak-proof system up to 100 psi (7 Bar) is required. This threaded inline hot air heater is designed for high pressure AND higher inlet temperature air applications needing a 1.25" MNPT fitting on the inlet and exit ends. This HIGH TEMPERATURE hot air heater provides a maximum process heat of 1652 degrees F at 11 SCFM by providing 6000/8000 maximum watts at 208/240 volt 1P power and 29/34 max. amps. The heater is 1.7" OD by 22" long with a 316 stainless steel housing. The recommended minimum airflow for this heater is 3 SCFM (85 SLPM), and the maximum inlet temperature should be no higher than 1000 degrees F.

These heater elements are shipped in a box containing 2 pieces. Heater elements must be ordered in multiples of 2 pieces! Price is the cost for one heater element.



The 076634 (or F076634) TUTCO SUREHEAT Hot Air tool provides a triple pass exchange housing. The Serpentine VI heater's triple pass exchange housing uses incoming air to travel (AND COOL) down the outside shell of the heater. The air then travels through a slot and into air holes, where it rapidly warms as it flows over the heater element and exits out of the heater. This hot air heater provides a maximum process heat of 1500 degrees F by providing 6,000 watts at 240 volt power and 25 max. amps. The heater is 10.88" long with a 1.25" outside diameter. The housing for this heater is part number 057088.

These heater elements are shipped in a box containing 2 pieces. Heater elements must be ordered in multiples of 2 pieces! Price is the cost for one heater element.

The 076635 (also known as F076635) TUTCO SUREHEAT Hot Air tool provides a triple pass exchange housing. The Serpentine VI heater's triple pass exchange housing uses incoming air to travel (AND COOL) down the outside shell of the heater. The air then travels through a slot and into 4 air inlet holes, where it rapidly warms as it flows over the heater element and exits out of the heater. This hot air heater provides a maximum process heat of 1500 degrees F by providing 8,000 watts at 240 volt power and 33.3 max. amps. The heater is slightly longer at 11 inches (A dimension) with a 1.25 inch outside diameter (B dimension) and a radiused end to minimize any cold air gaps within your housing.

F076753 Sureheat Max Control Panel is designed for 240 volt 3 phase power with 30 amps and 60Hz. It can be used for the F074724 and F074728 Sureheat Max Heaters.

F076754 Tutco SureHeat Max and Max HT Control Panel is designed for 480 volt 3 phase power with 30 amps and 60Hz. It can be used for the F074726, F074731, F074734, and F077083 Sureheat Heaters.

F076755 or 076755 Tutco Sureheat Max/Max HT Control Panel is designed for 240 volt 3 phase power with 60 amps and 60Hz. It can be used for the 074732 and 077081 TUTCO SUREHEAT Heaters.

F076756 or 076756 Sureheat Max/Max HT Control Panel is designed for 480 volt 3 phase power with 60 amps and 60Hz. It can be used for the 074736 and 077085 Sureheat Heaters.

F076905 or 076905 Tutco Sureheat Max Control Panel is designed for 380/400 volt 3 phase power with 30 amps and 50/60Hz. It can be used for the 074725, 074729, and 077082 TUTCO SUREHEAT Max/Max HT Heaters.

F076906 or 076906 Tutco Sureheat Max/Max HT Control Panel is designed for 380/400 volt 3 phase power with 60 amps and 50/60Hz. It can be used for the 074735 and 077084 Tutco Sureheat Heaters.

The 077028 (or F077028) TUTCO SUREHEAT threaded inline heater is a Style B design which will have slight air leakage through the power wire strands, and it can handle up to 150 psi (10 bar). This threaded inline hot air heater is designed for high pressure air applications needing a 1.25" NPT sized heater. This hot air heater provides a maximum process heat of 1400 degrees F by providing 8000 maximum watts at 240 volt Single or Three Phase power and 33.3 (1PH) or 19.2 (3PH) max. amps.