CER-1/4-20 Ceramic Terminal Bases and Caps offer high temperature insulating protection for standard screw terminals on mica heater bands, ceramic heater bands, mineral Insulated band heaters, channel heaters, finned strip heaters, and mica strip heaters. Ceramic terminal bases and caps help to provide an electrically safe environment in your manufacturing facility, and these high temperature bases are very easy to install. This ceramic terminal base (CER-1-4-20) mates with the Ceramic Cap pictured in the product image. The thread is 1/4" by 20. 5 SETS ARE INCLUDED, (ONE SET=ONE BASE AND ONE 1/4-20 THREADED CAP).

039272-90 TUTCO SUREHEAT air heater 90 degree probe Type k thermocouple with an exposed tip for faster reaction time. The type k thermocouple has a 3/16" diameter probe with an exposed tip to quickly sense the exit air temperature. This thermocouple tip should be mounted 1" or less (0.5" is better) from the exit air opening.

42734 Mineral Insulated, Compression Style Thermocouple. This Type J Thermocouple Has A Bendable Probe That Is 3/16" Diameter By 26" Long. It Has 24" Fiberglass Insulated Leads With Stainless Steel Braiding. This Thermocouple Is Ungrounded. 3/8" OD x 1-1/4" Long Transition Fitting with Strain Relief Spring. Two-Pin Mini Plug with mating Two-Hole Mini Jack INCLUDED. 1/8" NPT Compression Fitting INCLUDED. 

42735 Mineral Insulated, Compression Style Thermocouple. This Type K Thermocouple Has A Bendable Probe That Is 3/16" Diameter By 4" Long. It Has 24" Fiberglass Insulated Leads With Stainless Steel Braiding. This Thermocouple Is Ungrounded. 3/8" OD x 1-1/4" Long Transition Fitting with Strain Relief Spring. Two-Pin Mini Plug with mating Two-Hole Mini Jack INCLUDED. 1/8" NPT Compression Fitting INCLUDED. 

The Band Heater Inner Diameter Is 9.438", and the one-time expandable Band Heater Width Is 4.0". The Band Heater Has Post Terminals And Dual Voltage. The Band-heater Is 240/480 Volts And 4000 Watts. Compare To the 5032153c, 10000712, or 5033194 Heater Bands. The Pictured Band Heater Is For Reference Only.

A1P-24-80 Avatar Triac Power Controller--has a 1 to 7 day lead time to build! This controller can be used for controlling Tutco SureHeat industrial electric hot air heaters.

The A1P-24-80 power controller features:

208-240VAC Single Phase 50/60 Hz
80 amps
Phase Angled Fired
Output Voltage can be 0 to 97% of input voltage
4 to 20 mA at 5 volts DC, 250 Ohms Input Control Signal

C1p-12-20 Avatar Power Controller

4022-17 Ceramic Wire Connectors Are The Twist-lock Or Nut Style Made For 10-12 Awg Wire. These Porcelain Wire Connectors Are Rated For High Temperature Thermocouple Wire Applications For Up To 300 Deg C With A Maximum Voltage Of 300. These Connectors Can Handle Solid Thermocouple Wire Or Stranded Thermocouple Wire. Pack Of 62 Pieces

4022-17 Ceramic Wire Connectors Are The Twist-lock Or Nut Style Made For 10-12 Awg Wire. These Porcelain Wire Connectors Are Rated For High Temperature Thermocouple Wire Applications For Up To 300 Deg C With A Maximum Voltage Of 300. These Connectors Can Handle Solid Thermocouple Wire Or Stranded Thermocouple Wire. Pack Of 62 Pieces

The GSU-202-120-CT urn heater is made for applications requiring 120 volt power single phase and 2000 watts. In the urn heater diagram that is shown below, the "A" overall heater length dimension is 7.5 inches, the "B" inside tank height is 1.375 inch, and the "C" width dimension is 3 inches.

The GSU-302-208-CT replacement urn heater is made for applications requiring 208-volt power single phase and 3000 watts. In the urn heater diagram that is attached below, the overall heater element length dimension is 6.75 inches (was 7.5 inches), the inside tank height is 2.125 inches (was 1.375 inches), and the heater element width is 3-1/16 inches (was 3 inches). This heater comes with two copper (was stainless steel) sheath tubular elements that are silver brazed into a brass header. This heater is also supplied with a standard 4-inch square or octagon conduit box.

This GSU-302-CT drop-in replacement urn heater is made for applications requiring 240-volt power single phase and 3000 watts, and it has a thermal cutout.

The GSU-402-208-CT urn heater is made for applications requiring 208 volt power single phase and 4000 watts. In the urn heater diagram that is shown below, the "A" overall heater length dimension is 9.5 inches, the "D" inside tank height is 2.125 inch, and the "C" width dimension is 3-1/16 inches. This heater comes with two COPPER sheath tubular elements that are silver brazed into a brass header. This heater is also supplied with a standard 4 inch conduit box.
The Glenn Electric/ Backer Marathon cross reference part numbers are GSU-402-208-CO or 10-6385-11. An optional thermal cut-off is supplied with this immersion heater.

The GSU-402-CT comparable urn heater is made for applications requiring 240 volt power single phase and 4000 watts. For this urn heater, the "A" overall heater length dimension is 9.50", the "D" inside tank height is 2.125", and the "C" width dimension is 3-1/16" (was 3 inches). This heater comes with two copper (was stainless steel) sheath tubular elements that are silver brazed into a brass header. This heater is also supplied with a standard 4 inch square conduit box. The heater needs a minimum 2-7/16" (was 2-3/8 inch) diameter hole for installation. 

The GSU-502-208-CT similar urn heater is made for applications requiring 208 volt power single phase and 5000 watts. In the urn heater diagram that is shown below, the "A" overall heater length dimension is 11 inches, the "B" inside tank height is 2.25 inch, and the "C" width dimension is 4 inches.

The GSU-502-CT urn heater is made for applications requiring 240 volt power single phase and 5000 watts. In the urn heater diagram that is shown below, the "A" overall heater length dimension is 12.75 inches, the "B" inside tank height is 1-5/16 inch, and the "C" width dimension is 4 inches.

The GSU-503-208-CT urn heater has been obsoleted and is an immersion heater built with a lower watt density to provide a long heater life and dependable performance.

The TTUH-CO-60 urn heater is made for applications requiring 208 volt power single phase and 6000 watts. In the urn heater diagram that is attached below, the "A" overall heater length dimension is 14.5" (was 13.5 inches), the "B" inside tank height is 2.125" (was 1 inch), and the "C" width dimension is 4" (was 4 inches).

The GSU-602-CT SIMILAR urn heater is made for applications requiring 240 volt power single phase and 6000 watts. In the urn heater diagram that is shown below, the "A" overall heater length dimension is 13.5 inches, the "B" inside tank height is 1 inch, and the "C" width dimension is 4 inches.

The GSU-703-CT urn heater is made for applications requiring 240 volt power three phase and 7000 watts. In the urn heater diagram that is shown below, the "A" overall heater length dimension is 11 inches, the "B" inside tank height is 2.25 inch, and the "C" width dimension is 4 inches.

This Type K Thermocouple Is A Similar Replacement For Oem G429533 Temperature Sensor. The Temperature Measurement Is Done With A Grounded Sensing Probe Sheath That Is 3/16" Diameter By 1" Length And Made From 304 Stainless Steel. The Leads Have Fiberglass Protection With Stainless Steel Overbraid And They Are 48" Long. There Is A Standard Two Pin Male Plug (Color: Yellow) On The End With A Cable Clamp For Wear Resistance.

This TL1-KHM004AU1F082A-19 Type K Thermocouple is Mineral Insulated and is used to read bean temperatures during coffee roasting. It has these features:

1/8" Diameter By 4" Probe Length Inconel 600 Sheath
Ungrounded

82" of High Temperature (800F) Fiberglass Leads with Stainless Steel Braid protection

0.375"OD by 1.25" Transition Fitting with Ceramic Potting* rated for 1200F (used for minimal moisture and vibration)

2" stripped bare lead termination

*For applications in an environment with more moisture and/or vibration, then Epoxy potting is recommended for temperature exposures up to 450F. Call Jobco at 479-424-1300 to have your custom thermocouple made to meet your needs.

This K Thermocouple Ntk72m8a Has A M8 X 1threaded Melt Probe For K-type Thermocouple Applications. This Is A High Temperature Thermocouple For Continuous Usage At -328 To 2100 Degrees F. The Temperature Probe Has A 1/2" Swivel Section That Can Fit Into Shallow Holes, And Provide Accurate Thermcouple Readings In Deeper Holes, Too. This High Temperature Sensor Has 72" Of Stainless Steel Braid Leads With Spade Lugs On The End.

This K Thermocouple Ntk72m8 Has A M8 X 1threaded Melt Probe For K-type Thermocouple Applications. This Is A High Temperature Thermocouple For Continuous Usage At -328 To 2100 Degrees F. The Temperature Probe Has A 1/2" Swivel Section That Can Fit Into Shallow Holes, And Provide Accurate Thermcouple Readings In Deeper Holes, Too. This High Temperature Sensor Has 72" Of Stainless Steel Braid Leads With Spade Lugs On The End.

This K Thermocouple Ntk72m8b Has A M8 X 1threaded Melt Probe For K-type Thermocouple Applications. This Is A High Temperature Thermocouple For Continuous Usage At -328 To 2100 Degrees F. The Temperature Probe Has A 1/2" Swivel Section That Can Fit Into Shallow Holes, And Provide Accurate Thermcouple Readings In Deeper Holes, Too. This High Temperature Sensor Has 72" Of Stainless Steel Braid Leads With Spade Lugs On The End.

10 Mgt (105str) Hw05801001 High Temperature Power Lead Wire, 10 Awg (Sold In 100 Foot Roll)

10-01tggt (105str) Hw05701001 High Temperature Power Lead Wire, 10 Awg (Sold In 100 Foot Roll)

Hw05701201 High Temperature Power Lead Wire, 12 Awg (Sold In 100 Foot Roll)

C41401 14-01tggt High Temperature Power Lead Wire, 14 Awg (Sold In 100 Foot Roll)

Wire-18-01 Tggt Hw05701801 High Temperature Power Lead Wire, 18 Awg (Sold In 100 Foot Roll)